Skip to the content

Why the PS5 uses liquid metal, and what that means if you open one

Last updated: By Corey Thornton9 min readCooling & Thermals

Why the PS5 uses liquid metal, and what that means if you open one

Yes, the PS5 uses liquid metal, not thermal paste, between its main processor and the heatsink. Sony showed it in its official teardown video in October 2020, and its PS5 Pro teardown in 2025 confirmed the approach carried over to later models. For owners, liquid metal in the PS5 changes the maintenance rules. Cleaning dust through the removable covers is a job Sony documents step by step. Opening the console to repaste the chip is not, and the liquid metal is the main reason to leave that part alone. Below: what Sony built, why it suits a console, what goes wrong when owners dig in, and the cleaning routine that is safe.

Liquid metal in the PS5: what Sony built

The teardown video, posted to the PlayStation YouTube channel on October 7, 2020, was presented by Yasuhiro Ootori of Sony's mechanical design team. Coverage at the time picked out the liquid metal as the surprise. GamesBeat reported Ootori's explanation that the chip is a small die running at a very high clock rate, which concentrates a lot of heat in a small area, and quoted him directly: "The PS5 utilizes liquid metal as the TIM to ensure long-term, stable, high-cooling performance." TIM is thermal interface material, the layer between chip and cooler. He also said Sony had spent more than two years preparing the change.

The containment is the part that matters for owners. GSMArena noted the foam padding Sony placed around the chip in the video. GamesBeat and iFixit both pointed to a Sony patent for an insulating, foam-cushioned enclosure that keeps the metal on the surface of the chip. When iFixit took a retail console apart a month later, it found the shiny alloy on the processor under a steel plate held down by many screws, and concluded that the sealed-in liquid metal could be challenging to replace during service.

Sony kept it. The PlayStation Blog's PS5 Pro teardown, published in April 2025 with the Pro's mechanical and electrical design leads, describes liquid metal as a technology carried over to successive PS5 models. For the Pro, Sony added fine grooves where the liquid metal is applied so that the cooling effect is more stable. The same post says the Pro's heat pipes are copper and the silver parts of its heatsink aluminum, with more heat pipes than the standard console.

Why liquid metal suits a console

On a desktop PC, liquid metal is mostly a hobbyist's gamble. In a console it makes more sense, for reasons that come straight from the way consoles are built.

Factor In a game console On a home PC
Who applies it A factory process with a measured amount and a fitted barrier You, with a syringe and a swab
Containment Designed in from the start Tape and nail polish, if you remember
Service Sony says there are no user-serviceable parts inside Repasting is routine maintenance
Thermal cycling Daily warm-ups and cool-downs for years Same, but you can repaste when paste pumps out
Heat density A small, fast chip with high heat per square millimeter Varies widely

Ootori's point about heat density is the core of it. A small die makes the joint between chip and heatsink the bottleneck, which is the same reason delidders put liquid metal under a heat spreader (our delid guide covers that case). Paste would have been the easy choice; as GamesBeat summed up Sony's reasoning, it was not good enough for this chip.

Long life is the other point. Ordinary paste slowly pumps out of a joint that heats and cools every day; our comparison of liquid metal and thermal paste explains how both age. A console has to keep the same performance for years without anyone opening it. A sealed, well-contained metal layer suits that job, provided it stays where the factory put it.

The rest of the cooler is built for the same goal. GSMArena describes the fan as 120 mm in diameter and 45 mm thick, pulling air in from both sides. iFixit noted the large heatsink with copper heat pipes, and the dust ports Sony designed so the owner can vacuum the cooling path without going inside.

Why owners should not repaste a liquid metal PS5

Repasting a PC is a routine job. Repasting a PS5 is not the same job with a different screwdriver. Here is what changes.

Getting there disturbs the containment. Past the covers you meet security Torx screws, metal shields and the steel plate iFixit had to unscrew. The barrier around the chip is a fitted part of the design. Once you have lifted the heatsink, you cannot be sure you have put the barrier back the way the factory built it, and Sony publishes nothing that would tell you.

The metal moves. Gallium alloys stay liquid at room temperature and cling to many surfaces. A bead that rides out on the heatsink or a cotton swab and lands on the small components around the processor can short the board, sometimes not until the console has heated and cooled a few times.

Paste is a step down. Replacing the metal with paste swaps in the material Sony passed over for this chip. The likely result is higher temperatures and more fan noise, and paste in a hot joint pumps out with time.

Reapplying metal is guesswork. The amount, the spread and, on the Pro, the grooved surface are factory decisions. Too much is how spills happen. Too little leaves dry patches.

It is rarely the fix. A PS5 that runs loud or shows a heat warning usually has a simpler cause. Sony's manual says that if the console shows its high temperature message, you should turn it off, let it cool, move it somewhere well ventilated and check that the vents are not blocked. If you have fitted an M.2 SSD, it also says to check that the drive's heat-dissipation parts have not come loose. Start there.

Cleaning dust safely, the way Sony documents it

Sony's instruction manual recommends a handheld vacuum cleaner for dust on the vents, and recommends taking the covers off to vacuum the dust trapped underneath. Its support page for removing and attaching covers gives the steps. Pulled together, the routine looks like this:

  1. In the control center, select Power, then Turn Off PS5. Rest mode is not off.
  2. Unplug the AC power cord and all cables, and wait for the console to cool. Sony warns that it can be hot right after use.
  3. Lay a soft cloth on a flat surface and put the console on it.
  4. Remove the covers as Sony describes for your model. On the CFI-2000 and CFI-7000 models (the slimmer console and the Pro), remove the feet with the bottom facing up, then lift each cover slightly to free its clips. On the original CFI-1000 model, remove the base and pull each cover up and to the side as the support page shows.
  5. Vacuum the vents and the dust under the covers with a handheld vacuum, including the dust ports. Do not push anything into the fan or the vents.
  6. Wipe the outside with a soft, dry cloth. The manual says not to use alcohol, paint thinner, benzene, insecticide or chemically treated cloths on the plastic.
  7. Put the covers back until each clicks into place. Sony warns that covers installed incorrectly can make the console overheat.
  8. Reconnect the cables and power last, after checking the plug and the AC IN connector for dust.

Placement matters as much as cleaning. Sony's manual asks for at least 10 cm of space from a wall, no long-fiber carpet underneath, no cramped cabinet and no cloth draped over the console. A clean console in a closed cabinet can still overheat.

Warranty: what opening the console means

Sony's US limited hardware warranty, as printed in the PS5 Pro safety guide for the United States and Canada, runs for one year from purchase. It does not apply to damage caused by service from anyone who is not Sony or a Sony-authorized provider, or to damage caused by opening the product or any action taken inside it by anyone else. It also excludes consoles modified to alter capability or functionality without Sony's written permission. The UK manual is blunter: unauthorized modification voids the warranty, and there are no user-serviceable components inside.

Two nuances are worth knowing. Sony's own documents walk owners through removing the outer covers, vacuuming under them and fitting an M.2 SSD; going past the metal shields to the processor is where those instructions stop. And in the US, the FTC warned six major companies in 2018, including makers of video game systems, that conditioning warranty coverage on an unbroken seal is generally prohibited under the Magnuson-Moss Warranty Act. iFixit found that the PS5's tamper-evident sticker carries no warranty-void wording. Neither point helps if you short the board while repasting: damage you cause by opening the console is still yours.

So the practical rule is short. Inside the warranty, a PS5 with a cooling fault goes back to Sony. Outside it, a repair shop that already handles liquid metal consoles is a far better bet than a first attempt on the kitchen table. If you want to practice the skills, a PC is the place: start with anti-static basics and an ordinary paste job, where a mistake costs a cleanup instead of a console.

Sources and further reading

Wondering whether a cooler is enough? check the headroom with the cooler TDP calculator.

Headshot of Corey Thornton
Corey Thornton

Corey handles cooling: thermal paste, pads, delidding and liquid metal. He explains where the heat goes in plain numbers and is suspicious of any cooler box that prints a wattage without saying how it was measured.